De-Ionized Water Systems;
Water Softening Equipment;
Ion-Exchange Equipment;
Specialty Filters and Filtration Equipment;
Bacterial and Biological Filtration;
Reverse Osmosis and Membrane Filtration Equipment for Water and Waste
Purification;
Reverse Osmosis Drinking Water Plants;
Potable Water Plants;
Industrial Waste Treatment and Recycling;
Industrial water Recycling;
Hazardous Waste Consulting;
Heavy Metal Removal/Recovery;
Precious Metal recovery;
Cooling Tower and Boiler Chemistries and Controls;
Ozonation, Half-Oxygen, and singlet oxygen systems;
Electrocoagulation;
Environmental Consulting and Inspections (Phase I and Phase II);
Environmental Remediation (Phase III);
Emergency Spill Response;
Engineering Services;
and Permitting Services.
You are the
visitor since 12/12/04
TESTING
Advanced Coupon and Testing Co. offers services providing coupons and analysis for corrosion testing. We can guarantee
24 hours (weekday) turn around on test results. Coupons can be for waterborne studies like Cooling Towers and Boilers
or any other corrosion application. Advanced Water Engineering, Inc. was founded on the premise that there was
a definite need for a "QUALITY" commercial/industrial water and waste treatment company that designs
and provides equipment and service at reasonable rates. It was founded in 1986 and incorporated under the laws
of Florida in 1989. AWE, Inc. is comprised of four divisions: Advanced Water Engineering, Inc.; Advanced Environmental
Engineering, Inc.; Advanced Water Treatment, and Advanced Caribbean Tank.
Advanced Water Engineering, Inc. is a group of engineering specialists that design, can manufacture, and market
any grade of water or waste treatment equipment including professional engineering services and permitting as required
by local, state, or federal agencies. AWE's customer base is comprised of high tech electronics, aerospace, medical
and industrial institutions and manufacturing. The chemical service division (AWT) provides design, consulting,
installation and routine service for the operation and maintenance of Cooling Towers, Boilers, and other Heat Transfer
equipment. The tank division (ACT) is the largest supplier of polyethylene storage tanks to the Bahamas, Caribbean,
and South America. The environmental division (AEE, Inc.) provides environmental Phase I and Phase II Environmental
Surveys and designs and manufactures equipment for environmental remediation and recycling. Since its founding,
Advanced Water Engineering, Inc. has expanded from a regional company to an international corporation.
AWE, Inc. can be hired as engineering consultants, pilot plant operators, and/or equipment vendors.
We specialize in all types of water purification from particulate filtration to semiconductor grade De-Ionized
water.
Results can be provided by fax, or e-mail and can be incorporated into Spreadsheet format. Results can be expressed
in English or Metric units but are normally expressed in mils/yr.
Advanced Coupon and Testing Co. Advanced Water Engineering, Inc. offers many methods of producing De-Ionized Water
(DI). We offer dual bed De-Ionization by ion exchange, Mixed bed De-Ionization by ion exchange, two pass and multipass
Reverse Osmosis, and E-Cell® electrodeionization (EDI). We also offer DI water heaters.DUAL BED DI (DI) MIXED
BED DI (MBDI) REVERSE OSMOSIS (RO) E-CELL® DEIONIZED WATER HEATERS
?
HOME PAGE
CLICK ON THE PHOTO OR THE LINK
?
DI water heater details DI water heater options and specs
Heating Coil:
1.Double wall tubing with leak detection port
(F30 and F60 sizes only).
2.Alternate tubing materials:
Admiralty, 90/10 Copper-Nickel,
Stainless Steel (Type 304 or 316),
Other:_______________
Note: Tubing materials other than copper
will exhibit lower maximum capacities. To
determine actual capacity, multiply the GPM
rating on page 6 by the following:
0.95 Admiralty
0.81 90/10 Copper-Nickel
0.81 Stainless Steel
Steam Shell
3.Alternate shell construction:
Cast Steel, Cast Bronze, 90/10
Copper-Nickel, Stainless Steel
(Type 304 or 316),
Other:____________
Operating Controls
4.In order to limit the steam pressure in the heat
exchanger shell a steam pressure reducing valve is
factory supplied and shipped loose for in-the-field
installation.
5.Single solenoid safety system opens the sensing line to
the blending valve in order to limit the hot water output
in the event of an over temperature condition. Requires
5 Amp, 120 Volt service.
6.Double solenoid safety system opens the sensing line
to the blending valve as well as closing the steam
supply to the heat exchanger in the event of an over
temperature condition. Requires 5 Amp, 120 Volt
service.
7.All steam components (traps, strainers) shall be Cast
Steel construction.
8.If water hardness exceeds 120 ppm, scale build-up can
reduce efficiency. A factory packaged Klean-Koil KitTM
with built-in connections will allow for quick and easy
in-place cleaning of the coil to remove these deposits
thereby avoiding long periods of down time and
expensive maintenance costs.
9.All 316 Stainless Steel wetted part construction for use
in Deionized water applications.
nRecirculation Packages (pump by
others):
10.Fixed temperature (____ oF) 3-way diverting valve, one
(1) 1" globe valve, and two (2) 1" check valves are
shipped loose for in-the-field installation.
11.Same as Option 10 except the 3-way diverting valve has
an adjustable range.
12.Option 10 or 11 is factory fitted and piped to the water E-CELL® DEIONIZED WATER SYSTEMS?
Advanced Water Engineering, Inc. offers E-Cell® electrodeionization (EDI) as an authorized GE® systems
integrator. E-Cell® replaces Mixed bed de-ionizers and uses electrical current to perform contimuous regeneration.
The current is used in place of hazardous regeneration chemicals. Neutralization of regenerant waste is no longer
necessary. E-cell® is especially cost effective in new facilities where Acid, Caustic, and Neutralization facilities
will not have to be constructed or manitained. Information on the standard E-Cell® stack and Pharmaceutical
Stack can be found by clicking this link in pdf format. We also offer DI water heaters.
CLICK BELOW TO SEE INFO ON OUR AUTOMATIC BACKWASHING MICROFILTRATION SYSTEMS MICROLITE TURBODISK BAG FILTER
MICROVENT TANK AIR VENT FILTERS THESE SYSTEMS ARE ALSO AVAILABLE IN MANUAL BACKWASH CONFIGURATIONS. CLICK HERE
TO SEE MANUAL TURBOSDISKS MANUAL TURBODISK LIQUID BAG FILTRATION SYSTEMS
The AWE bag filtration system offers a wide variety of high flow high efficiency filtration options from 0.3 micron
to 24 mesh up to 1000 gpm. Multiple units can be used in parrallel to achieve any flowrate or parallel to separate
different micron ratings for segregation and recovery or extended bag life and efficiency.
? ? ?
Our standard housings can be constructed in Carbon steel, Aluminum, 304 or 316 stainless steel. We offer both screw
type lids and clamp lids for closure. Custom housings can be made to withstand pressures up to 5000 psi and any
chemical. We stock many housings and can make and ship housings for next day delivery.CLICK HERE TO VIEW OUR BAG
FILTER SYSTEM SIZING GUIDE
Click the link to see prints of (in adobe format):
SINGLE 2"NPT 180 GPM ----- ALTERNATING DUAL 1-1/4"NPT 180 GPM
SINGLE 2"NPT 180 GPM (SCREW NUT LID ) ----- ALTERNATING DUAL 2"FLANGED 180 GPM
SINGLE 3" FLANGED 250 GPM ----- DUAL NON-VALVED 3"NPT 360 GPM
SINGLE 3" NPT 250 GPM ----- DUAL VALVED 3" NPT 360 GPM
MULTIBAG 360 GPM 3" FLANGED ----- DUAL 360 GPM 4" FLANGED
MULTIBAG 4" FLANGED 750 GPM -----We stock nearly all standard bag sizes and can have custom bags made quickly
from any material and micron rating. We offer both sewn and welded bag seams as well as different bag ring sizes,
shapes and materials.PLEASE E-MAIL US WITH ALL OF YOUR WATER TREATMENT QUESTIONS!! WE'LL ANSWER THEM ASAP
OUR MICROFILTRATION SYSTEMS
AWE's auto-backwashing microfiltration systems can be used to filter down to 1 micron on flows from 6 to 6000 gpm.
This equipment was originally designed to for Giardia and Cryptosporidium removal from municipal systems.
These systems use downflow filtration and upflow backwash using a patented ceramic filter media. Excellent results
can be obtained at as high as 10 gpm/sqft filtration rates. They can easily filter in the 3-5 micron range without
additional chemical or polymer feed systems. The media is also inert and compatible with respect to polymers, acids,
caustics, and oxidants while maintaining indefinite service life. Water use efficiency can be as high as 98%.
?
Typical applications are:
1) Municipal filtration systems for dirt, algae or
and some bacteria;
2) Iron and Manganese removal;
3) Pre-filtration for Reverse Osmosis,
Nanofilters or sub-micron filtration;
4) Giardia and Cryptosporidium removal;
Available features are:
1) Proven community process and design;
2) Stainless Steel distributors;
3) High quality Spun Fiberglass tanks;
4) GF-pneumatic valving or top mount valving;
5) Air sparging;
Options:
1) PLC based automation packages w/NTU
discriminators or DP switches;
2) Integrated instrumentation;
3) Chemical feed packages;
4) Raw water and/or backwash pumps;
5) Backwash collection/recovery systems.
Mechanical Turbodisk Filtration Systems
The Turbodisk* system is a fully automatic system designed for side-stream cooling tower applications. It removes
sand, silt, dirt, sediment, as well as airborne contaminants like seedes, algae, bugs, and leaves. It has advantages
over sand style backwashing systems in that it uses a fraction of the backwash water.
????
Backwashing can be performed in a little as 10seconds using only 3.5 gallons of water when using option air sparging
equipment. A minimum of 45 psi is required for backwash. Optional pressure boosting equipment that operates ONLY
during backwash is also available.
CLICK HERE FOR MANUAL MODELS ONLY ?
Standard equipment includes:
1) Automatic filter/disk cartridges;
2) Stainless Steel inlet/outlet Manifolds;
3) Auto-backwash Valves/Solenoids;
4) Backwash Controller;
5) Stainless Steel leg assembly;
6) Pump and motor starter relay;
7) Pressure maintaining valves;
8) Skid assembly can be stainless or plastic;
9) Air-override feature to enhance backwash efficiency.
Options Include:
1) Isolation valves;
2) Pump pre-strainers;
3) Air compressor.
Tech Data Mechanical Turbodisk Filtration Systems
The TurboMAN system is a MANUAL system designed for SMALL filtration applications such as slow producing wells,
commercial applications and large homes. It removes sand, silt, dirt, sediment, as well as airborne contaminants
like seeds, algae, bugs, and leaves up to 100 gpm (larger models are available. It has advantages over sand style
backwashing systems in that it uses a fraction of the backwash water.INSIDE VIEW INDUSTRIAL MODEL MANUAL MODEL
Backwashing can be performed in a little as 30 seconds using only 15 gallons of water. A minimum of 45 psi and
35 gpm is required for backwash. Optional pressure boosting equipment that operates ONLY during backwash is also
available.
Standard equipment includes:
1) filter/disk cartridges;
2) pressure gauge ports.
Tech Data SMALL HOME REVERSE OSMOSIS SYSTEMS HOME PAGE
Residential RO systems are mainly used to remove common contaminants from city or well waters. Our Reverse Osmosis
Home systems are smaller versions of our commercial units that are manufactured for in-home dialysis use and feedwater
for industrial environmental test chambers. Filtered water is forced past a semi-permeable membrane where dissolved
solids and large organic molecules are collected and disposed and "purified" water passes through the
membrane. The "purified" water is collected and stored for further use such as drinking and cooking.
We manufacture Home RO's in two versions, 15 gallon per day (gpd) and 25 gallon per day. Custom units with more
capacity or storage are available in many configurations. We only offer industrial grade TFC® style membranes
unless special applications dictate otherwise. All materials are NSF or FDA approved or compliant. Typical specifications
are as follows: *when proper maintenance is performed and feedwater temp 77F;60psi feed w/atmospheric discharge;500ppm
TDS feed; HVAC CHEMICAL SERVICE AND TREATMENT PROGRAMS ??
Advanced Water Engineering, Inc. is pleased to introduce our Chemical Program to treat your cooling towers open
and closed loop cooling HVAC systems. We presently are responsible for more than 200 cooling towers and have a
greater market share than any competitor in our area. Our program provides you with the methods and tools to remove
the worry from maintaining your system and you can rely on our prompt courteous service. Our home office is in
Brevard County, Florida and our satellite office is in Tequesta, Florida. We have a fully trained chemical specialist
with 32 years of Water treatment experience who is supervised by a degreed Chemical Engineer with 20 years of water
treatment experience on local staff. All of our field service technicians have at least technical Bachelors Degrees
in Chemistry or Biology.
COOLING WATER/CHILLED LOOPS:
Our programs provide chemicals, service, testing reagents, and inspection supervision for
scheduled events. These programs will control Scale, Corrosion, Algae and Slime. A custom tower program will be
developed for each make-up water supply, if necessary. We use no low pH treatment programs, acid chromates, or
magnets. Unlike most of our competitors, all of our chemistries are EPA approved for their appropriate (cooling
tower, boiler water, coag, etc...) use. EVERY EFFORT IS MADE TO OPTIMIZE EACH TOWER TO MAXIMIZE COST EFFICIENCY.
Advanced Water Engineering, Inc. will train your engineering/maintenance personnel to properly maintain chemical
balance in their systems. We will also visit each site as often as our contract specifies with each customer specifies
to check and verify the chemical testing, make observations and recommendations, and necessary mechanical adjustments
to controllers. Each visit , recommendation, and action can be recorded electronically and e-mailed in a spreadsheet
format report in addition to the on-site log sheets.
TYPICAL SYSTEMS
OPEN LOOP
Open loop chemistries are designed to control Scale, Corrosion, and Biological growth in atmospheric evaporators.
As heat energy is carried away by evaporated water, the water's salt content increases. When the salt content reaches
pre-determined limits, the tower "blows down" the salty water and replaces it with fresh water until
the tower is back in it's "operating range". More chemical is added to maintain the proper chemical level
which prevents the fresh water from contributing to scale or corrosion.
Biocides are usually "pot fed" to open loop systems to control biological growth. During this operation,
blow down is halted for a designated period of time while disinfection occurs. We also offer continuous Bromine
feeders for small tower applications.
We provide the necessary materials, supplies, and service for treatment of the open loop cooling system. Our single
or multiple component system (tech data sheets available) will control scale and corrosion on properly operating
systems. Please click HERE to read a specification for our controllers.
To monitor effectiveness of our program, a Certified Coupon Program (CCP) will be developed to satisfy each customers
maintenance engineer per the existing scope of work. Coupon data will be correlated and electronically sent to
the maintenance engineer.
We will collect and compile the customers' system testing data and provide a complete four
week report to the Maintenance Engineer.
Extra chemical used at each site will be on-site, including a copy of their MSDS's which will be posted at each
site.
CLOSED LOOP CHILLED and HOT WATER
Closed loop chemistry is based upon scavenging Oxygen to prevent corrosion. These systems are usually stable and
once they have been started up properly, chemical consumption is usually VERY low. Chemical addition is usually
only necessary when make-up water is added due to a system leak or system maintenance. It can also be heavily consumed
if there are suction leaks on the recirculating pumps.
We provide all start-up closed loop (hot and chilled) corrosion control chemical (tech data sheets are available).
After start-up, we check each closed loop at least quarterly and individually more often if notified that there
was a leak or repair on a particular system. Maintenance personnel should also test each closed loop after repairs.
Chemical additions will be made at our next scheduled visit after repairs or immediately after our personnel test
the loop and find it out of spec. If pot feeders are not in proper working order at each location, we can provide
them.
CHEMICAL CONTROLLERS
Chemical Control of the Cooling Towers and atmospheric evaporators consists of TOTAL DISSOLVED SOLIDS CONTROL(TDS)
of a BLOWDOWN SOLENOID with a FEEDER PUMP and POT FEEDER CONTROL with a FEEDER PUMP of the Biocide. Most towers/coolers
have existing operating TDS controllers with feed pumps. Please click HERE to read a specification for our controllers.
All of the systems should have Biocide lockout timers and pumps. We have many ways to provide the above controls:
CONTROL SYSTEMS
We will strive to attempt unity and compatibility of all of the controls systems at a reasonable cost. We have
extensive experience with the Lakewood®, Advantage®, LMI®, Pulsatron®, Morr®, and Hydac®
equipment. Please click HERE to read a specification for our controllers. Our effort is to be as cost effective
as possible, along with the maintenance department, in choosing which system to install in each location. Spare
controls and pumps will be available on a limited basis to keep systems operating while choices are being made.
The customer may opt to replace the entire control rather than simply adding the Biocide timers. Factory warranties
would then apply to the entire control rather than just the Biocide portion of the controls.
OPTION 1: COMPLETE REPLACEMENT
In the cases where there are no existing probes (such as a new tower or one where TDS control is presently not
employed) or that a failed controller's probes are incompatible with a new controller, we will add a NEW fully
programmable controller with a Chemical Injection feed pump for each chemical being dosed. Please click HERE to
read a specification for our controllers. Our fully programmable controllers will control the TDS Blowdown , chemical
feed pump, Biocide pump and Biocide timer and lockout . This system consists of the complete control system, chem
pumps, and solenoid required to operate a tower; (spec sheets available).
OPTION 2: SEMI-COMPLETE REPLACEMENT
In the cases where existing controllers have failed and are compatible, we simply replace the controls and possibly
add pumps. This will entail using the existing probes, plumbing, and pumps;Please click HERE to read a specification
for our controllers.
OPTION 3: BIOCIDE SYSTEM INSTALLATION
We believe, that in most cases, a Biocide lockout timer and pump is necessary. We will add a fully programmable
lockout timer with pump. This will add the biocide feature to all of the towers. Please click HERE to read a specification
for our controllers.
OPTION 4: BLOWDOWN SOLENOID
Blowdown solenoids are responsible for bleeding the salty water from the towers. Some frequently clog with suspended
solids. Should a particular tower clog often, or should a solenoid/valve fail, we will replace it with a Quick
Clean style solenoid and valve and recommend types of solids filtration for the towers(s).
MAINTENANCE
We include normal calibrations, probe maintenance, controller set-up and adjustment, pump adjustment, and solenoid
cleaning in the cost of our proposals.
We stock rebuild kits and maintenance parts for the majority of the control systems and pumps.
Our service rate will apply to installation/repair of all (non-routine adjustment) components on a case by case
basis as some installations are much more difficult to repair/service than others.
CAPITAL EQUIPMENT
We also can provide, install, and repair Marley®, BAC®, DELTA®, and EVAPCO® Cooling towers. Our
installation staff are fully trained in maintenance and repair of these towers including PLC's and Variable frequency
drives and Variable speed drives. We can provide new or rebuilt recirculation pumps including Aurora Pumps®,
B&G Pumps®, Armstrong pumps®, TACO Pumps®, Grundfos Pumps®, LMI Pumps®, Pulsatron Pumps®,
Chemtech® and many others. We specialize in water conserving sand/silt/dirt removal systems including HARMSCO®,
GAF®, LAKOS®, Turbodisk®, Macrolite®, and many other options.
ORIENTATION
A complete orientation package will be presented to appropriate individuals prior to implementation of the service.
A pre-orientation meeting will be requested after Contract award to work out details for the Orientation Meeting.
AFFILIATION
Apperson Chemical Co. presently manufactures and blends our treatment chemicals. We have their FULL backing, lab,
and technical support should they be needed. In addition, we are affiliated with Advanced Coupon and Testing Company
to perform coupon/corrosion studies.
TOWER AND HEAT EXCHANGER CLEANING
Our staff is fully trained and familiar with procedures for cleaning cooling towers and heat exchangers. We have
a run-ready trailer fully equipped with chemical tanks and pumps for onsite cleaning. Our customer can choose between
various stocked cleaners such as SAFE D SCALE® non-acid non-fuming non-corrosive environmentally safe cleaners
and our Ex-Scale Rodine® inhibited HCl formulations.
BOILERS:
Proper boiler treatment requires that boilers remain clean and free of scale. Scale causes a layer of insulation
that inhibits heat transfer thus requiring much more energy use. Scale also allows a safe haven for corrosive bacterial
growth. Our staff is fully trained and familiar with procedures for cleaning boilers. We have a run-ready trailer
fully equipped with chemical tanks and pumps for onsite cleaning. Our customer can choose between various stocked
cleaners such as SAFE D SCALE® non-acid non-fuming non-corrosive environmentally safe cleaners and our Ex-Scale
Rodine® inhibited HCl formulations.
All boilers should be periodically inspected and cleaned. Accurate measurements should be taken of feedwater for tds (or conductivity), M and P alakalinity, Total hardness, and any other local scale-forming compound(s).
HOT WATER/STEAM CLOSED LOOPS:
Closed loop chemistry is based upon scavenging Oxygen and volatile amine complexes to prevent corrosion. Hot water
systems are usually stable and once they have been started up properly, chemical consumption is usually VERY low.
Chemical addition is usually only necessary when make-up water is added due to a system leak or system maintenance.
It can also be heavily consumed if there are suction leaks on the recirculating pumps.
We provide all start-up closed loop corrosion control chemical (tech data sheets are available). After start-up,
we check each closed loop periodically. Maintenance personnel should also test each closed loop after leak repairs.
If pot or other required feeders are not in proper working order at each location, we can repair or provide them.
BOILER TREATMENT
Old boilers will require a complete flush and possible acid clean with one of our above
cleaning systems. Ex-Scale should be made up at 10% by volume or Safe D Scale at 10-33% by volume. Addition of
our CWT239 to 1000 ppm as Nitrite and MBC-215 microbiocide will begin the anti-corrosion process. This usually
takes about 8 gallons of CWT 239 and 1/2 gallon of MBC215 per 1000 gallons.
Water softeners are a must on nearly all boiler water feed. They must be capable of continous zero soft water.
Small low-pressure boilers can tolerate a few ppm of hardness. As a water treatment equipment manufacturer, we
are capable of replacing or repairing nearly any brand of softener.
Our BWT-269 boiler treatment program requires that sulfites be controlled between 30 and 60 ppm. TDS should be
controlled at a maximum of 3500 tds un-neutralized or 2100 tds neutralized. p-Alkalinity must be controlled to
a maximum of 1000 ppm. This will provide polymer in the boiler bottoms to scavenge scale causing contaminants and
neutralizing amine complexes in the condensate lines via morpholine.
To properly control small boilers, you will need a least and alkalinity test kit good to 10 ppm (m and p), a sulfite
kit good to 10 ppm, a total hardness kit good to 2 ppm, a Nitrite test kit good to 10 ppm and a Myron L model EP-10
conductivity meter with a range up to 10,000 mmhos.
On larger boilers, automatic blow-down and chemical feed systems should be used.
We also have complete programs for Large industrial and power boilers not covered above.
Please don't hesitate to call or e-mail if you need more info or clarification! Our SAFE-D-SCALE will remove Calcium,
hardness, and other scale products easily without the worries normally associated with Inhibited and non-inhibited
Hydrochloric Acid descalers. One can pour this descaler into their hand and dissolve pieces of scale without harm.
SAFE-D-SCALE will not harm steel copper or other base metals.
SAFE-D-SCALE is:
Non-hazardous
Non-toxic
Biodegradable
Non-corrosive
Our descaler products are specifically designed to safely and rapidly dissolve all water-formed fouling deposits (such as rust, scale, lime, calcium, marine growth, etc.) from any water-operated equipment.
They're completely safe for use in all types of commercial kitchen equipment or any institutional application for deposit descaling operations.
They may be safely flushed down regular sewer systems with a water flush.
? ?
SAFE-D-SCALE IS ROUTINELY AVAILABLE IN ONES, FIVES, AND 55'S. PLEASE CONTACT US ABOUT CABOUYS, TOTES, OR BULK SHIPPING.
TECHNICAL CAPABILITIES ? HOME PAGE
Advanced Water Engineering, Inc. was founded on the premise that there was a definite need for a "QUALITY"
commercial/industrial water and waste treatment company that designs and provides equipment and service at reasonable
rates. It was founded in 1986 and incorporated under the laws of Florida in 1989. AWE, Inc. is comprised of four
divisions: Advanced Water Engineering, Inc.; Advanced Environmental Engineering, Inc.; Advanced Water Treatment,
and Advanced Caribbean Tank.
Advanced Water Engineering, Inc. is a group of engineering specialists that design, can manufacture, and market
any grade of water or waste treatment equipment including professional engineering services and permitting as required
by local, state, or federal agencies. AWE's customer base is comprised of high tech electronics, aerospace, medical
and industrial institutions and manufacturing. The chemical service division (AWT) provides design, consulting,
installation and routine service for the operation and maintenance of Cooling Towers, Boilers, and other Heat Transfer
equipment. The tank division (ACT) is the largest supplier of polyethylene storage tanks to the Bahamas, Caribbean,
and South America. The environmental division (AEE, Inc.) provides environmental Phase I and Phase II Environmental
Surveys and designs and manufactures equipment for environmental remediation and recycling. Since its founding,
Advanced Water Engineering, Inc. has expanded from a regional company to an international corporation.
AWE, Inc. can be hired as engineering consultants, pilot plant operators, and/or equipment vendors.
We specialize in all types of water purification from particulate filtration to semiconductor grade De-Ionized
water. We also design, manufacture or represent:
Reverse Osmosis systems from 15 gallons per day to 400 gallons per minute for water or waste treatment;
Specialty filtration from standard particulate filtration to catalyst recovery (including standard, medical grade,
and industrial cartridges, resins, and filter media);
Standard filtration that includes cartridges, bags filters, backwashable medias, and other systems for particle
removal;
Cooling Tower and Boiler Water chemical treatment and control systems;
Point-Source Waste Treatment of organics and hazardous metal recovery including special ion-specific resins, DI
water recirculation, and electrowinning;
Precious metal recovery;
Environmental Consulting services;
Dialysis Equipment, installation, design, and
consulting; and
Public water systems. OZONE GENERATION EQUIPMENT
Advanced Water Engineering, Inc. applies ozone technology in many ways. We manufacture or represent industrial
grade ozone generation systems from 0.5 UV generated grams per hour (gph) to 50 corona discharge pounds per day
(ppd). These systems can be used in many applications. Such applications are pure water sanitization, sterilization,
and maintenance of bacteria free closed loop pure water systems in the pharmaceutical, food processing, or electronics
manufacturing; hydrogen sulfide destruction in residential, commercial, municipal, and industrial raw water and
sewage treatment; BOD and COD reduction; organic chemical destruction as effluent from pharmaceutical and aerosol
packaging operations.
The bulk of our systems are used in hydrogen sulfide removal and pharmaceutical packaging operations such as packagers
of suntan lotions, oils and creams.
These systems can be provided complete with air prep, oxygen concentrators, or direct oxygen feed. Typical systems
are provided with ozone injection, recirculation pumps, and lop feed pumps, all on a single skid.2#/day system
at major pharmaceutical plant DVANCED WATER ENGINEERING, INC. has saved many customers thousands of dollars by
recovering their disolved Palladium FOR RECYCLING. Palladium is used as a plating catalyst for electroless plating
in circuit board manufacturing and semiconductor processes. It is also a primary ingredient in catalytic converters.
We have several viable processes that can immediately recover your waste palladium for recycling.
We also have two MAJOR circuit board manufacturers recovering thousands of dollars per month right now. Our recovery
process can recover up to 40 troz of Palladium for an operating cost of $1500.00 (At this writing, Palladium was
approaching $1000/troz. Advanced Water Engineering, Inc. has hundreds of systems specifically designed and tuned
to removing and/or recovering precious metals such as Gold, Palladium, Silver, etc.... These systems are capable
of removing these metals selectively so that system capacity is not wasted on contaminants or non-precious metals,
non-precious cations or anions. Collection medias are typically shipped to refiners and converted to the raw metal
form for cash exchange.
The recovery systems simply remove precious metals from the waste or recovery stream for further processing or
return the water to the process as DeIonized water.
Most of these systems are in PCB (Circuit Board) manufacturing operations but we also have systems in semi-conductor
and other metal finishing facilities. Advanced Water Engineering, Inc. has over 400 systems either scavenging or
recycling water from heavy metal rinsewaters at plating operations. These system can be regenerated at the recycling
location, on-site, or off-site at one of our hazardous waste processing facilities. The heavy metal regenerant
can be further processed by batch or continous sludging or by metal recovery.
The scavanging systems simply remove unwanted metals from the waste stream for further processing. Recycling systems
return the water to the process as DeIonized water.
Most of these systems are in PCB (Circuit Board) manufacturing operations but we also have systems in semi-conductor
and other metal finishing facilities. SAMPLE PERFORMANCE ?
Public Water Systems by Advanced Water Engineering, Inc.:
Wingate Reserve, Melbourne Beach, Fl. - a 120,000 gpd public water REVERSE OSMOSIS system that incorporates Hydrogen
Sulfide removal, Chlorination/Dechlorination, RO, blend, re-chlorination, 30,000 gallon Clearwell, and distribution
to the community. This system was specifically designed to remove high TDS, radionucleides (Radium 226, 288), and
hydrogen Sulfide from the Floridan Aquifer.
Lighthouse Cove, Melbourne Beach, Fl. - a 24,000 gpd public water REVERSE OSMOSIS NANOFILTRATION system that incorporates
Hydrogen Sulfide removal, Chlorination/Dechlorination, RO, blend, rechlorination, 30,000 gallon Clearwell, and
distribution to the community. This system was specifically designed to remove high TDS, radionucleides (Radium
226, 288), and Hydrogen Sulfide from the Floridan Aquifer.
South Brevard Community Center, Micco, Fl.- a 60 gpm peak public water system that incorporates Ion-Exchange Iron
Removal, Ion Exchage color removal, Softening, Clearwell Chlorination and distribution. This system was specifically
designed to remove high Iron and Color from local shallow wells.
South Brevard 7th Day Adventist Church, Grant, FL - a small public transient non-community church water system
rated at 400 gpd that includes chlorination and color removal.
Summit Cove, Micco, FL- a 120 gpm water softening system for a local community.
Camelot RV Park, Provided specific media for adsortion of color on a community water system capable of providing
200 gpm.
Kodiak Island Air Force Missile Launch Complex, Rebuilt and properly repaired existing Vickery water systems to
remove high levels of sand silt and dirt, added LSI increasing equipment, and set-up for proper operation by adding
Turbodisk filtration and injection chemistry.
Commercial/Industrial Water Systems by AWE, Inc:.
Hydroage, Inc., Cocoa Fl- a 36,000 GPD REVERSE OSMOSIS System that incorporates Reverse Osmosis, blend, Hydrogen
Sulfide removal, storage, and re-pressurization. The system was specifically designed to provide water for Hydroponic
Farming.
Accurate Metal Finishing of FL, Rockledge, FL- a 15,000 GPD DeIonized water system incorporating Dechlorination,
De-Ionization, Storage and repressurization. Acid, Caustic, and regenerant waste is about 40% of a traditional
system requiring greater than 1 Mega-Ohm/cm water. This system was specifically designed for the metal finishing
industry.
MIcroVia Circuits, Winter Springs, FL- a 25,000 GPD De-Ionized water system incorporating Dechlorination, De-Ionization,
15,000 storage w/UV, and repressurization. Acid, Caustic, and regenerant waste is about 40% of a traditional system
requiring greater than 10 Mega-Ohm water. This system was specifically designed for the electronics industry.
Brown & Williamson, Macon, Ga- several Reverse Osmosis based 75 GPD RO systems for high quality re-humidification.
These systems were specifically designed to protect environmental test chambers from local city water components.
Naples Artificial Kidney Center, Naples, Fl- a 4500 gallon per day REVERSE OSMOSIS system with Softening, Dechlorination,
Reverse Osmosis, emergency de-ionization, storage, and repressurization loop w/UV. This system was specifically
designed to meet AAMI pure water needs to a major dialysis center.
Disney World Swan Hotel Reedy Creek, FL- A 600 gpm twin softening system to provide soft water to the Hotel laundry.
Happy Octopus Car Wash Cape Canavaral, FL designed and built 3000 gpd Reverse Osmosis spot free water system for
brushless spot free car wash.
Lake County Public School System, Lake County, FL- An FDA/EPA/DEP approved proportional control chemical injection
system for corrosion control an a private water system providing service water to a large school.
INET, Kennedy Space Center, FL - desgned, provided, and installed small public water systems that incorporate storage
with Ozone recirculation, Pure Water Storage, gravity flow sanitary waste and Industrial waste storage, and Ozone
destruct.
Space Station Processing Center, Kennedy Space Center, Fl- designed and built a mobile high purity water system
that incorporates sub-micon particle filtration, de-ionization, de-oxidation (oxygen removal), TOC removal, and
mobile monitoring equipment. This system was specifically designed to meet high purity, less than 10 ppb TOC, and
less than 10 ppb dissolved Oxygen, and no detectable dissolved gasses for water re-circulation loops on the space
station and satellites.
Cape Canveral Air-Force Station Delta Launch Facility (SLC-37), Cape Canveral, FL- Designed, Installed and provided
2000 and 6000 gallon poly tanks with 200 gpm 316 ss 3 micron and 20 micron bag filtration systems plumbed sch 80
CPVC for Caustic, Acid passivation, and ultrapure rinsing of 316 ss and titanium Liquid Oxygen and Liquid Hydrogen
storage and transfer stations to the Launch Pad.
KIWI Tennis Club, Indian Harbour Beach, FL- designed, manufactured, and installed a 15,000 GPD reverse osmosis
system with 9000 gallons of corona discharge ozonated storage and stainless steel represurization system for 9
clay tennis courts by Welch Tennis Courts of Sarasota, FL. Feedwater quality was 2200 ppm with a product water
quality less than 50 ppm.
Industrial Waste Systems by Advanced Water Engineering, Inc.:
Advanced Board Circuitries, FL- designed and provided materials for industrial waste water recycling equipment
for circuit board manufacturer. The systems consist of Ion-Exchange based recycling equipment to remove organics,
heavy metals, and anions. The systems provide purified water for re-use. Water use in-plant was reduced from 7,000,000
gallons per month 2,500,000 gallons per month.
Axon Circuits, FL- designed and provided equipment for preciuos metal Palladium recovery. The system incorporated
specially designed ion-exchange resins to recover the precious metal from waste streams.
Axon Circuits, FL- designed and provided equipment for end-of-pipe waste water purification for re-use in electronics
manufacturing. The Membrane based system recovers 30,000 gallons per day.
Peavey Incorporated, Meridian, MI- a system desgned to recover copper up to 50 ppm from an alkaline etching operation
waste stream at up to 200 gpm.
Major Texas based Pharmaceutical Co, Brownsville, Texas- a custom designed scavenging system for distribution and
scavenging of radioactive chemotherapy manufacturing waste.
ABHE & SVOBODA, Cutler, ME- a custom designed wastewater recycling system designed to remove paint chips, sand,
silt, dirt, Chrome, Lead, and PCB's from a 40,000 psi water blasting operation using FLOW® brand high pressure
water blasters. System was designed for 60 gpm.
KIWI Tennis Club in Indian harbour Beach, FL, is a state of the art premium tennis facility. The sport the highest
quality Clay tennis courts manufactured and installed by Welch Tennis Courts of Sarasota, FL. These courts have
the advantage of fast dry with a sub-surface irrigation system, constructed of either HydroGrid or HydroCourt.
These systems reduce irrigation costs, cut maintenance time and personnel costs and eliminate down time completely.
These courts require irrigation water for proper maintenance. Due to drought conditions in Florida, the local water
company refused supply water for court maintenance. This is when Welch turned to Advanced Water Engineering, Inc.
to
The Floridan Aquifer in this area is presently about 2500 ppm of Salts level (TDS). It was our job to treat the
water in a manner to reduce the TDS to optimum levels for long court life. We designed and manufactured a 15,000
gallon per day Reverse Osmosis system with 9,000 gallons of on-site storage, corona discharge ozone recirculation
of stored water, stainless steel repressurization pumps, and final partical filtration. Final water quality was
35 ppm.REVERSE OSMOSIS SYSTEMS FROM 100 TO 22,500 GALLONS PER SEA WATER SYSTEMS FRESH AND BRACKISH WATER SYSTEMS
Storage tanks can also be purchased at www.advancedwater.com/tankpage.html . We can also size repressurization
skids for distribution with UV, Ozone, Chlorine, or Bromine disinfection
SEAWATER REVERSE OSMOSIS DESALINATORS FROM 100 TO 6000 GALLONS PER DAY
?
HOME PAGE
Seawater desalination (water purification) can be acomplished easily by high pressure Reverse Osmosis. AWE SWPRO
systems are available as a complete frame mounted assemblies for large boats or land based installations or as
component kits for sailboats or tight places. They are available as drinking quality units or purifiers. Since
purifiers produce water that is very pure (LSI is less than 0), plumbing and components MUST be plastic or non-corrodable
only. Product water from drinking quality units can be used with plastic or metal plumbing.
The following described units use Cat Brand pumps. Other brands or materials of construction are available. Units
are standard with 5 micron filtration. We can size additional filtration if neccessary.
Storage tanks can also be purchased at http://www.advancedwater.com/tankpage.html . We can also size repressurization
skids for distribution with UV, Ozone, Chlorine, or Bromine disinfection.
CLICK HERE FOR SEAWTER 150-1500 GPD
CLICK HERE FOR SEAWATER 7,000-20,000GPD
? HOME PAGE
Advanced Carribean Tank Co. is the largest supplier of tanks to the Carribean. We stock hundreds of plastic tanks
from Water Storage to Fuel Storage in Florida for immediate shipment.
CLICK ON TANK SKETCHES FOR LINK TO DESCRIPTIONS
Polyethylene water storage tanks are UV stabilized and very resiliant. A sledge hammer will simply bounce off the
tank causing no harm. They are very easy to add fittings and it can be done on-site with a minimum of non-specialty
tools. They are available from 50 to 15,000 gallons.
We also stock and sell tanks set up for municipal hypochlorite storage. Click here.PLEASE CALL (or e-mail by link
below) (321)-777-4909 ( US ) or TOLL FREE (877) 777-4909 SHOULD YOU HAVE IMMEDIATE NEEDS AS WE STOCK HUNDREDS OF
TANK SIZES FOR ALL APPLICATIONS........ READY FOR SHIPMENT NEED MORE INFO?????? info@advancedwater.com
CLICK HERE FOR UNDERGROUND SEPTIC OR CISTERN INSTALLATION INSTRUCTIONS PLEASE CALL (321)-777-4909 (or e-mail by
link below) SHOULD YOU HAVE IMMEDIATE NEEDS AS WE STOCK HUNDREDS OF TANK SIZES FOR ALL APPLICATIONS........ READY
FOR SHIPMENT CONE BOTTOM POLYETHYLENE STORAGE TANKS
AND
TANK STANDS HORIZONTAL LEG POLYETHYLENE STORAGE TANKS HOME PAGE
HYPOCHLORITE STORAGE TANKS
AWE, INC. is the largest supplier of tanks to the Carribean. We stock hundreds of plastic
tanks from Water Storage to Fuel Storage in Florida for immediate shipment.
We presently have THREE 8200 gallon (Real volume 8934 gal) and TWO 10,300 gallon (Real volume 10950 gal) tanks
ready for delivery in Tampa, Florida. These tanks were fully prepared cross-linked HDPE for Hypochlorite storage
for a local municipality. They were rejected because they were built in Natural poly color instead of black.
They have studs ready for ladders and fill pipes, titanium fittings with viton seals, and OR1000 lining. EACH TANK HAS 3" Self-aligning top-mount bulkhead fittings.
Pictures ARE IN THE PROCESS OF BEING posted ASAP. Click on the following links for pdf formatted
prints:
CLICK ON TANK LINKS SKETCHES FOR PRINTS AND DESCRIPTIONS:
8200 #1 8200 #2 8200 #3 10300 #1 10300 #2
CLICK HERE TO SEE A HAND SKETCH OF FITTING SIZE AND LOCATIONS
Asking Price is $11,500 for the 8200's and $13,500 for the 10,300's. This is about 25% off list. We can ship the
8200's for free within 250 miles of tampa, FL. The 10,300 will have to go std frt.
Polyethylene water storage tanks are UV stabilized and very resiliant. A sledge hammer will simply bounce off the
tank causing no harm. They are very easy to add fittings and it can be done on-site with a minimum of non-specialty
tools. They are available from 50 to 15,000 gallons.
PLEASE CALL (or e-mail by link below) (321)-777-4909 ( US ) or TOLL FREE (877) 777-4909 SHOULD YOU HAVE IMMEDIATE
NEEDS AS WE STOCK HUNDREDS OF TANK SIZES FOR ALL APPLICATIONS........ READY FOR SHIPMENT NEED MORE INFO info@advancedwater.com
CLICK HERE FOR UNDERGROUND SEPTIC OR CISTERN INSTALLATION INSTRUCTIONS PLEASE CALL (321)-777-4909 (or e-mail by
link below) SHOULD YOU HAVE IMMEDIATE NEEDS AS WE STOCK HUNDREDS OF TANK SIZES FOR ALL APPLICATIONS........ READY
FOR SHIPMENT OPEN TOP RECTANGUALR POLYETHYLENE STORAGE TANKS PICK-UP TRUCK POLYETHYLENE STORAGE TANKS UNDERGOUND
CISTERN TANKS
600 GAL 1200 GAL 1700 GAL CLICK HERE FOR UNDERGROUND CISTERN INSTALLATION INSTRUCTIONS UNDERGOUND SEPTIC TANKS
300 and 500 GAL SPHERE 500 GAL SEPTIC 1000 GAL SEPTIC SINGLE HOLE 1000 GAL SEPTIC DOUBLE HOLE CLICK HERE FOR UNDERGROUND
SEPTIC INSTALLATION INSTRUCTIONS VERTICAL POLYETHYLENE STORAGE TANKs USED WASTE AND WATER TREATMENT EQUIPMENT FOR
SALE
HOME PAGE 250 GPM 18M+ DI SYSTEM click link for details 140 GPM AND 170 GPM REVERSE OSMOSIS SYSTEM RO #1 RO #2
click link for details
NEARLY NEW USED 1 CUFT SLUDGE PRESS
click link for details
3000 GALLON PER DAY REVERSE OSMOSIS SYSTEM
click link for details
USED ONCE DORR-OLIVER 110 GPM WASTEWATER CENTRIFUGE
click link for details